Moin Moin!
Ich habe eine externe USB Festplatte, auf der verschiedene NTFS und FAT32 Partitionen sind.
Doch aus mir unerfindlichen Gründen kann ich nix davon mounten.
Ich habe nun schon Stunden zugebracht hier im Forum nach ähnlichen Problemen zu suchen und alle möglichen Dinge probiert, doch noch hat nix geholfen.
Folgendes habe ich probiert:
|
Quellcode
|
1
2
3
4
5
6
7
|
stephan@stephan:~$ lsusb
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 1668:0441 Actiontec Electronics, Inc. [hex]
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
stephan@stephan:~$
|
Ich habe nichts weiter an USB Geräten angesteckt, daher gehe ich mal davon aus, dass sich hinter Actiontec... meine Platte verstecken soll?
Das kam bei tail -f /var/log/messages raus:
|
Quellcode
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
|
Nov 6 02:00:23 localhost kernel: [4295161.451000] usb 4-3: new high speed USB d evice using ehci_hcd and address 10
Nov 6 02:00:24 localhost kernel: [4295161.855000] SCSI subsystem initialized
Nov 6 02:00:24 localhost kernel: [4295161.875000] Initializing USB Mass Storage driver...
Nov 6 02:00:24 localhost kernel: [4295161.884000] scsi0 : SCSI emulation for US B Mass Storage devices
Nov 6 02:00:24 localhost kernel: [4295161.887000] usbcore: registered new drive r usb-storage
Nov 6 02:00:24 localhost kernel: [4295161.887000] USB Mass Storage support regi stered.
Nov 6 02:00:24 localhost usb.agent[8912]: usb-storage: loaded successfully
Nov 6 02:00:29 localhost kernel: [4295166.887000] Vendor: SAMSUNG Model: SP 1604N Rev: TM10
Nov 6 02:00:29 localhost kernel: [4295166.887000] Type: Direct-Access ANSI SCSI revision: 04
Nov 6 02:01:45 localhost kernel: [4295242.957000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
Nov 6 02:02:03 localhost kernel: [4295261.345000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
Nov 6 02:02:21 localhost kernel: [4295279.733000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
Nov 6 02:02:32 localhost kernel: [4295290.020000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
Nov 6 02:02:42 localhost kernel: [4295300.245000] scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
Nov 6 02:02:42 localhost kernel: [4295300.245000] usb 4-3: USB disconnect, address 10
Nov 6 02:02:42 localhost kernel: [4295300.246000] sda : READ CAPACITY failed.
Nov 6 02:02:42 localhost kernel: [4295300.246000] sda : status=0, message=00, host=0, driver=04
Nov 6 02:02:42 localhost kernel: [4295300.246000] sda : sense not available.
Nov 6 02:02:42 localhost kernel: [4295300.251000] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0Nov 6 02:02:42 localhost scsi.agent[8977]: sd_mod: loaded sucessfully (for disk)
Nov 6 02:02:42 localhost kernel: [4295300.351000] usb 4-3: new high speed USB device using ehci_hcd and address 11
Nov 6 02:03:00 localhost kernel: [4295318.739000] usb 4-3: new high speed USB device using ehci_hcd and address 12
Nov 6 02:03:19 localhost kernel: [4295337.127000] usb 4-3: new high speed USB device using ehci_hcd and address 13
Nov 6 02:03:29 localhost kernel: [4295347.414000] usb 4-3: new high speed USB device using ehci_hcd and address 14
Nov 6 02:13:45 localhost -- MARK --
Nov 6 02:27:34 localhost kernel: [4296792.576000] drivers/usb/input/hid-core.c: input irq status -71 received
|
Da steht nun nix von Actiontec sondern die richtige Bezeichnung von Samsung.
Mit dmesg kam folgender output:
|
Quellcode
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
|
[4295161.451000] usb 4-3: new high speed USB device using ehci_hcd and address 10
[4295161.855000] SCSI subsystem initialized
[4295161.875000] Initializing USB Mass Storage driver...
[4295161.884000] scsi0 : SCSI emulation for USB Mass Storage devices
[4295161.887000] usb-storage: device found at 10
[4295161.887000] usb-storage: waiting for device to settle before scanning
[4295161.887000] usbcore: registered new driver usb-storage
[4295161.887000] USB Mass Storage support registered.
[4295166.887000] Vendor: SAMSUNG Model: SP1604N Rev: TM10
[4295166.887000] Type: Direct-Access ANSI SCSI revision: 04
[4295242.957000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
[4295246.019000] usb 4-3: device descriptor read/64, error -110
[4295261.182000] usb 4-3: device descriptor read/64, error -110
[4295261.345000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
[4295264.407000] usb 4-3: device descriptor read/64, error -110
[4295279.570000] usb 4-3: device descriptor read/64, error -110
[4295279.733000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
[4295284.745000] usb 4-3: device descriptor read/8, error -110
[4295289.857000] usb 4-3: device descriptor read/8, error -110
[4295290.020000] usb 4-3: reset high speed USB device using ehci_hcd and address 10
[4295295.032000] usb 4-3: device descriptor read/8, error -110
[4295300.144000] usb 4-3: device descriptor read/8, error -110
[4295300.245000] scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
[4295300.245000] scsi0 (0:0): rejecting I/O to offline device
[4295300.245000] usb 4-3: USB disconnect, address 10
[4295300.245000] scsi0 (0:0): rejecting I/O to offline device
[4295300.245000] scsi0 (0:0): rejecting I/O to offline device
[4295300.246000] scsi0 (0:0): rejecting I/O to offline device
[4295300.246000] scsi0 (0:0): rejecting I/O to offline device
[4295300.246000] scsi0 (0:0): rejecting I/O to offline device
[4295300.246000] sda : READ CAPACITY failed.
[4295300.246000] sda : status=0, message=00, host=0, driver=04
[4295300.246000] sda : sense not available.
[4295300.246000] sda: assuming drive cache: write through
[4295300.251000] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[4295300.257000] usb-storage: device scan complete
[4295300.351000] usb 4-3: new high speed USB device using ehci_hcd and address 11
[4295303.413000] usb 4-3: device descriptor read/64, error -110
[4295318.576000] usb 4-3: device descriptor read/64, error -110
[4295318.739000] usb 4-3: new high speed USB device using ehci_hcd and address 12
[4295321.801000] usb 4-3: device descriptor read/64, error -110
[4295336.964000] usb 4-3: device descriptor read/64, error -110
[4295337.127000] usb 4-3: new high speed USB device using ehci_hcd and address 13
[4295342.139000] usb 4-3: device descriptor read/8, error -110
[4295347.251000] usb 4-3: device descriptor read/8, error -110
[4295347.414000] usb 4-3: new high speed USB device using ehci_hcd and address 14
[4295352.426000] usb 4-3: device descriptor read/8, error -110
[4295357.538000] usb 4-3: device descriptor read/8, error -110
[4296792.576000] drivers/usb/input/hid-core.c: input irq status -71 received
[4296792.584000] drivers/usb/input/hid-core.c: input irq status -71 received
[4296792.592000] drivers/usb/input/hid-core.c: input irq status -71 received
|
Leider kann ich mit alldem nicht viel anfangen, da ich erst ein Linuxeinsteiger bin. Ich erkenne nur, dass zumindest etwas mit USB und meiner Platte erkannt wird. Doch sehe ich den Fehler nicht wirklich und wie ich den beseitigen kann.
Freue mich daher über jede Hilfe!
Danke und gute Nacht. :-)
PS: was ich glatt noch vergessen hab; ich nutze Ubuntu 5.10.